GEO D10

GEO D10 PRODUCT FEATURES
Components HF: 1x 3” voice coil, 1.4” throat 16Ω driver on a 5° hyperboloid reflective wavesource.
MF/LF (front-firing): 1x 12” (30cm) high excursion neodymium 16Ω driver.
LF (side-firing): 2x 8” (20cm) neodymium 8Ω drivers in series.
Height x Width x Depth 380 x 744 x 750mm (15” x 29 1/3” x 29.5”) including array assembly system
Rigging access to axis height 344mm(13.5”)
Shape 10° Trapezoid.
Weight: net 57kg (125.7lbs) including array assembly system.
Connectors 1x AMPHENOL EP6 6-pole socket In; 1x AMPHENOL AP6 6-pole connector Through.
Construction Baltic Birch ply with structured black coating.
Front finish Molded Dark Grey Metal Grill.
Flying points Integral flying system. Intercabinet angle adjustments = 0.2°, 0.315°, 0.5°, 0.8°; 1.25°, 2.0°,
3.15°, 5°, 6.3°, 8.0°, 10.0° (logarithmic steps)
SYSTEM SPECIFICATIONS GEO D10 WITH NX242 TDCONTROLLER
Frequency response [a] 60Hz – 19kHz ±3dB
Usable range @-6dB [a] 55Hz –20kHz ±6dB
Sensitivity 1W @ 1m [b] 105dB SPL nominal (103dB SPL wideband)
Peak SPL @ 1m [b] Configuration dependent (d)
Dispersion [c] Vertical plane: Configuration dependent [d]. Horizontal plane: Configurable 80°/120° Low Frequency:
Cardioid
Crossover frequency LF-MF: 300Hz Active MF- HF: 1.1kHz Passive or Active (internally configurable).
Nominal impedance HF: 16Ω; LF/MF front:16Ω LF rear: 16Ω.
Recommended amplifiers HF: 875 to 1550Watts into 4Ω MF/LF front: 1750 to 3100Watts into 4Ω
3x GEO D10 in Parallel LF rear section: 1750 to 3100Watts into 4Ω
4x GEO D10 in parallel HF: 1000 to 1800Watts into 4Ω MF/LF front: 2000 to 3600Watts into 4Ω
LF rear section: 2000 to 3600Watts into 4Ω
6x GEO D10 in parallel HF: 1650 to 3000Watts into 2Ω MF/LF front: 3300 to 6000Watts into 2Ω
LF rear section: 3300 to 6000Watts into 2Ω
SYSTEM OPERATION
Electronic Controller The NX242 Digital TDcontroller (with NXtension Card) presets are precisely matched to the GEO D
Series cabinets and include sophisticated protection systems as well as advanced cardioid
directivity DSP algorithms. Using GEO D Series cabinets without a properly connected NX242 &
NXTension Card will result in poor sound quality and can damage components.
Array Design Arrays of less than 3x GEO D10 will provide poor dispersion control and are neither
recommended nor supported.
SubBass GEO SUB directional sub extends system low frequency response down to 35Hz
Speaker Cables Active: 5(-) / 6(+): HF: 3(-) / 4(+):LF/MF Front: 1(-) / 2(+): LF Rear.
Passive: 5(-) / 6(+): Not Connected: 3(-) / 4(+):LF/MF/HF Front: 1(-) / 2(+): LF Rear.
Rigging System Please refer to the GEO D User Manual before any operation.
SHIPPING & ORDERING
Packaging GEO D are packaged individually or in groups of 3x in NEXO GEO D dollies. Order as GEO D10.

 

GEO SUB

GEO SUB ProDuCt FeatureS
Components 1x 18” (46cm) long excursion neodymium 8Ω driver
2x 12” (30cm) neodymium 16Ω drivers
Height x Width x Depth 552.5 x 744 x 1131mm (21 1/4” x 29 1/3” x 44 1/2”)
Shape 10° Trapezoid
Weight 86Kg (189.6lbs)
Connectors 2 x NL4MP SPEAKON 4 pole (In & Through).
Construction Baltic Birch ply finish with structured black coating.
Front Finish Moulded Black Metal Grill.
Flying Points Integral flying system. Intercabinet angle adjustments = 0.2°, 0.315°, 0.5°, 0.8°;
1.25°, 2.0°, 3.15°, 5, 6.3°, 8.0°, 10° (logarithmic steps).
SYSTEM SPECIFICATIONS GEO SUB with NX242 TDcontroller
Frequency response @-3dB [a] 38Hz – 300Hz
Usable range @-6dB [a] 35Hz – 500Hz
Sensitivity 1W @ 1m [b] 103dB SPL Nominal
Peak SPL @ 1m [b] 140-143dB Peak
Dispersion [c] Cardioid pattern over the entire useable bandwidth
(two channels of the NX242 are used for the process).
Directivity Index [c] Q = 4.3 & DI = 5.3dB over the entire useable bandwidth.
Crossover frequency X-Over Mode = 75Hz active / Overlap Mode = 300Hz through NX242 Digital TDcontroller.
Nominal impedance 2 x 8Ω.
Recommended amplifiers 2 amplifier channels are required for directional operation, each rated at 1000 to
2000Watts into 8Ω per channel.
SYSTEM OPERATION
Electronic Controller The NX242 Digital TDcontroller presets are precisely matched to the GEO SUB and include
sophisticated protection systems. Using the GEO SUB without a properly connected
NX242 Digital TDcontroller will result in poor sound quality and can damage components.
Speaker Cables The front loudspeaker of the GEO SUB is wired 2+ & 2- while the rear loudspeakers
are wired in parallel 1- & 1+. The GEO SUB must use separate cables from the main system.
Rigging System Please refer to the user manual before any operation.